Valley Sleeper on oblique adjacent roof

Valley Sleeper on oblique adjacent roof
Der schräge Anbau auf Kehlbohlen

This task model was challenging. Keeping track of the geometric lines to develop the valley sleeper rafter lines on the roof surface was confusing. However, I just needed to remember to draw perpendicular lines to the valley rafter in ground plan to the valley rafter on the roof surface plane to develop the correct valley sleeper plane lines. The witches cut is develop two different ways in the task model, by using two different elevation line heights.



Basic ground plan for the Valley Sleeper on oblique adjacent roof.


Drawing with the roof surface plane developed and some of the valley lines on the roof surface plane.

Zoomed in view of the valley lines, including the hidden bottom edge of the valley sleeper on the roof surface plane.

Drawing with the valley sleeper bird mouths lines developed.

Witches cut lines for the ground view of the valley sleeper rafters.


Witches cut lines for the valley sleeper rafters on the roof surface plane.


Method #two for developing the witches cut lines  and the lines for the valley rafter bevel on the roof surface at the peak of the valley sleeper rafters.



Checking my drawing with the 3D valley sleeper rafters.


Roof Planes.








Komentar

Posting Komentar

Postingan populer dari blog ini

Layover Valley Rafter Basics

Gambar
Before I get into the Hexenschnitt for the Layover Valley Rafter I needed to review the basic geometry that defines the layover valley rafter. I needed to make sure I could draw the layover valley rafter correctly in plan view (ground plan). Here's one method of a basic drawing using the layover valley rafter backing triangle to position the layover valley rafter material on the roof surface that defines the  layover valley rafter in plan view. The  layover valley rafter top bevel is easily defined by extending the  layover valley rafter backing triangle to the top of the  layover valley rafter. The other  layover valley rafter line in plan view is defined by the bottom edge of the  layover valley rafter material sitting on the  layover valley rafter backing triangle. (Roof Surface). The  layover valley rafter plan view lines at the intersection of the two roofs. I tried this method for drawing the  layover valley rafter, but this method seems to be slow of a process for determinin
Baca selengkapnya

Hip Rafter Edge Bevel and Backing Angle

Gambar
In complex roof framing there are 7 main roof framing angles. Hip Rafter Backing Angle Valley Sleeper Bevel Angle Plain Titl (DP) Main Plan Angle Adjacent Plan Angle  Main Profile Rafter Slope Angle Adjacent Profile Rafter Slope Angle In this article I will discuss the hip rafter backing angle and the valley sleeper bevel angle. These two angles determine the miter angle and and saw blade bevel angles for jack rafters and purlin rafters that are plumb to the earth and for jack rafters and purlin rafters that are skewed from the eave line. A thorough knowledge of these two angles is critical in complex roof framing using geometry or trigonometry. The hip rafter edge bevel was avoided in the 12th century on some roof structures by rotating the hip rafter into the roof surface plane. However, by avoiding the hip rafter edge bevel, the carpenters-builders had to have a knowledge of the Valley Sleeper Bevel Angle. They didn't call it the Valley Sleeper Bevel Angle, but it's the same
Baca selengkapnya

Layover Valley Rafter Hexenschnitt #3

Gambar
In the book Das neue Buch vom alten Wissen der Schiftung The new book on the ancient knowledge Schiftung The new book on the ancient knowledge Roof Framing The new book on the ancient knowledge Roof Framing Geometry by Bernd Küppers I'm stuck on page 23. The geometry in the book, just doesn't return the correct miter angle for the Layover Valley Rafter Witches Cut (Hexenschnitt). I don't know if I'm drawing it incorrectly, or the BE (Bottom Edge Plane of the Layover Valley Rafter) should be drawn differently. Similar drawing at File: Kehlbohle mit Hexenschnitt.jpg There's 3 canted planes that define the Layover Valley Rafter Witches Cut Miter Angle. The main roof surface, the square tail fascia plane of the main roof and the the square tail fascia plane of the adjacent roof.  I think the problem with my geometric drawings is defining the intersection of the roof surface with the adjacent  square tail fascia plane.
Baca selengkapnya