Tréteaux Roof Framing Kernel and Claw Lines


The basic roof framing kernel can be used to develop the footprint of the hip rafter rotated into the roof surface. The roof framing kernel can also be used to verify the geometry of the claw lines on the fold down roof surface for the geometric development of the jack rafters, purlin rafters and purlin rafters skewed from the plate line.

tréteau à devers





Here's the basic roof framing kernel.



Add the hip rafter backing triangle to the roof framing kernel.



The red square at the top of the hip rafter backing triangle represents the hip rafter material you're using and it is rotated to align with the top of the hip rafter backing triangle. 

Geometric drawing steps for the rotated hip rafter foot print.
  1. Draw line FP #1 parallel with the hip rafter run line.
  2. Draw lines TC #1 & TC #2 parallel with the sides of the rotated hip rafter block in the hip rafter backing triangle.
  3. Where the TC # 1 line intersects at the bottom of the hip rafter backing triangle draw the line DP #1 to the eave line where it intersects with FP #1.
  4. Draw DP #2 parallel to DP #1.
  5. Draw the FP #2 line for the footprint line in plan view of the hip rafter. 
  6. The hip rafter foot print line intersects the two DP lines and forms the , yellow, hip rafter prism footprint. 




To develop the claw lines for the jack rafters, purlin rafters and skewed purlin rafters develop the roof surface. Use the Tréteaux Angles Check Online Calculator to draw out the claw lines on the roof surface or develop the claw lines from the geometry circled in the following drawings. 

Drawing #1
Roof Eave Angle = 90.00000
SS = Main Rafter Slope Angle = 30.25644
S = Adjacent Rafter Slope Angle = 39.80557

DD = Main Plan Angle = 55.00798
D = Adjacent Plan Angle = 34.99202

DD = arctan (sin W ÷ (tan SS ÷ tan S + cos W)) = 55.00798

R1 = Hip Rafter Slope Angle = 25.54245
C5m Main Hip Rafter Backing Angle = 16.79517
C5a Adjacent Hip Rafter Backing Angle = 31.63186
Valley Sleeper Saw Blade Bevel Angle = 90° - (C5m + C5a) = 41.57297

P2m = Main Jack Rafter Side Cut Angle = 31.15906
90° - P2m = Main Roof Sheathing Angle = 58.84094
P2a = Adjacent Jack Rafter Side Cut Angle = 47.66035
90° - P2a = Adjacent Roof Sheathing Angle = 42.33965
Purlin Depth = 1
Hip Rafter Depth = 2
Hip Rafter Width = 2

Purlin Rafter Seat Line Dimension for Plan View = 1.56205
Purlin Rafter Seat Line Dimension for Roof Surface = 1.20000
Hip Rafter Footprint Seat Line Dimension = 3.96927

Hip Rafter Dimension for Claw Lines from A to B = 1.78640
Hip Rafter Dimension C for Upper Claw Lines from A to C = 1.12740
Hip Rafter Dimension D for Lower Claw Lines from B to D = 0.88700




Drawing # 2
Roof Eave Angle = 120.00000
SS = Main Rafter Slope Angle = 30.25644
S = Adjacent Rafter Slope Angle = 39.80557

DD = Main Plan Angle = 76.99608
D = Adjacent Plan Angle = 43.00392

R1 = Hip Rafter Slope Angle = 29.61276
C5m Main Hip Rafter Backing Angle = 6.51019
C5a Adjacent Hip Rafter Backing Angle = 27.91566
Valley Sleeper Saw Blade Bevel Angle = 90° - (C5m + C5a) = 55.57415

P2m = Main Jack Rafter Side Cut Angle = 11.28135
90° - P2m = Main Roof Sheathing Angle = 78.71865
P2a = Adjacent Jack Rafter Side Cut Angle = 39.47840
90° - P2a = Adjacent Roof Sheathing Angle = 50.52160

Purlin Depth = 1
Hip Rafter Depth = 3.5
Hip Rafter Width = 3.5

Purlin Rafter Seat Line Dimension for Plan View = 1.56205
Purlin Rafter Seat Line Dimension for Roof Surface = 1.20000
Hip Rafter Footprint Seat Line Dimension = 6.94622

Hip Rafter Dimension for Claw Lines from A to B = 1.39221
Hip Rafter Dimension C for Upper Claw Lines from A to C = 0.68538
Hip Rafter Dimension D for Lower Claw Lines from B to D = 1.45905




Drawing #3
Roof Eave Angle = 90.00000
SS = Main Rafter Slope Angle = 33.69007
S = Adjacent Rafter Slope Angle = 33.69007

DD = Main Plan Angle = 45.00000
D = Adjacent Plan Angle = 45.00000

R1 = Hip Rafter Slope Angle = 25.23940
C5m Main Hip Rafter Backing Angle = 23.09347
C5a Adjacent Hip Rafter Backing Angle = 23.09347
Valley Sleeper Saw Blade Bevel Angle = 90° - (C5m + C5a) = 43.81306

P2m = Main Jack Rafter Side Cut Angle = 39.76216
90° - P2m = Main Roof Sheathing Angle = 50.23784
P2a = Adjacent Jack Rafter Side Cut Angle = 39.76216
90° - P2a = Adjacent Roof Sheathing Angle = 50.23784

Purlin Depth = 1
Hip Rafter Depth = 2
Hip Rafter Width = 2

Purlin Rafter Seat Line Dimension for Plan View = 1.80278
Purlin Rafter Seat Line Dimension for Roof Surface = 1.50000
Hip Rafter Footprint Seat Line Dimension = 3.60555

Hip Rafter Dimension for Claw Lines from A to B = 1.81221
Hip Rafter Dimension C for Upper Claw Lines from A to C = 1.04231
Hip Rafter Dimension D for Lower Claw Lines from B to D = 0.95940




Drawing for location of Miter & Claw lines on a roof with a Plumb Hip Rafter.


Roof Eave Angle = 90.00000
SS = Main Rafter Slope Angle = 30.25644
S = Adjacent Rafter Slope Angle = 39.80557

DD = Main Plan Angle = 55.00798
D = Adjacent Plan Angle = 34.99202

R1 = Hip Rafter Slope Angle = 25.54245
C5m Main Hip Rafter Backing Angle = 16.79517
C5a Adjacent Hip Rafter Backing Angle = 31.63186
Valley Sleeper Saw Blade Bevel Angle = 90° - (C5m + C5a) = 41.57297

P2m = Main Jack Rafter Side Cut Angle = 31.15906
90° - P2m = Main Roof Sheathing Angle = 58.84094
P2a = Adjacent Jack Rafter Side Cut Angle = 47.66035
90° - P2a = Adjacent Roof Sheathing Angle = 42.33965
Purlin Depth = 2
Hip Rafter Depth = 2
Hip Rafter Width = 2

Hip Rafter Claw & Miter Line Dimensions for Plumb Hip Rafters

Main SS Hip Rafter Offset Perpendicular to Hip Rafter Run Line = 1.34228
Man SS Hip Rafter Offset Along Eave Line = 1.63846
Adjacent S Hip Rafter Offset Perpendicular to Hip Rafter Run Line = 0.65772
Adjacent S Hip Rafter Offset Along Eave Line = 1.14692
Hip Rafter Backing Depth on Side of Hip Rafter = 0.40514

Hip Rafter Claw & Miter Line Dimensions for Plumb Hip Rafter on Main Side SS-DD
Hip Rafter Line Dimensions for Line 1 = 0.00000
Hip Rafter Miter Line Dimensions for Line 2 = 1.40209
Hip Rafter Miter Line Dimensions for Line 3 = 2.00574
Hip Rafter Claw Line Dimensions for Line 4 = 0.29525
Hip Rafter Claw Line Dimensions for Line 5 = 6.92159

Jack Rafter Miter Angle On Stick = 59.74356
Jack Rafter Bevel Angle On Stick= 31.15906
Jack Rafter Claw Angle on Stick = 8.87615
Jack Purlin Rafter Miter Angle On Side Face Perpendicular To Roof Surface On Stick= 70.57176
Jack Purlin Rafter Bevel Angle On Face Set In Roof Surface On Stick = 58.84094
Jack Purlin Rafter Claw Angle on Stick= 14.48201






































Komentar











Posting Komentar



















Postingan populer dari blog ini









Layover Valley Rafter Basics




















Gambar







Before I get into the Hexenschnitt for the Layover Valley Rafter I needed to review the basic geometry that defines the layover valley rafter. I needed to make sure I could draw the layover valley rafter correctly in plan view (ground plan). Here's one method of a basic drawing using the layover valley rafter backing triangle to position the layover valley rafter material on the roof surface that defines the  layover valley rafter in plan view. The  layover valley rafter top bevel is easily defined by extending the  layover valley rafter backing triangle to the top of the  layover valley rafter. The other  layover valley rafter line in plan view is defined by the bottom edge of the  layover valley rafter material sitting on the  layover valley rafter backing triangle. (Roof Surface). The  layover valley rafter plan view lines at the intersection of the two roofs. I tried this method for drawing the  layover valley rafter, but this method...








Baca selengkapnya










Hip Rafter Edge Bevel and Backing Angle




















Gambar







In complex roof framing there are 7 main roof framing angles. Hip Rafter Backing Angle Valley Sleeper Bevel Angle Plain Titl (DP) Main Plan Angle Adjacent Plan Angle  Main Profile Rafter Slope Angle Adjacent Profile Rafter Slope Angle In this article I will discuss the hip rafter backing angle and the valley sleeper bevel angle. These two angles determine the miter angle and and saw blade bevel angles for jack rafters and purlin rafters that are plumb to the earth and for jack rafters and purlin rafters that are skewed from the eave line. A thorough knowledge of these two angles is critical in complex roof framing using geometry or trigonometry. The hip rafter edge bevel was avoided in the 12th century on some roof structures by rotating the hip rafter into the roof surface plane. However, by avoiding the hip rafter edge bevel, the carpenters-builders had to have a knowledge of the Valley Sleeper Bevel Angle. They didn't call it the Valley Sleeper Bevel Angle, but it's the same...








Baca selengkapnya










Layover Valley Rafter Hexenschnitt #3




















Gambar







In the book Das neue Buch vom alten Wissen der Schiftung The new book on the ancient knowledge Schiftung The new book on the ancient knowledge Roof Framing The new book on the ancient knowledge Roof Framing Geometry by Bernd Küppers I'm stuck on page 23. The geometry in the book, just doesn't return the correct miter angle for the Layover Valley Rafter Witches Cut (Hexenschnitt). I don't know if I'm drawing it incorrectly, or the BE (Bottom Edge Plane of the Layover Valley Rafter) should be drawn differently. Similar drawing at File: Kehlbohle mit Hexenschnitt.jpg There's 3 canted planes that define the Layover Valley Rafter Witches Cut Miter Angle. The main roof surface, the square tail fascia plane of the main roof and the the square tail fascia plane of the adjacent roof.  I think the problem with my geometric drawings is defining the intersection of the roof surface with the adjacent  square tail fascia plane.








Baca selengkapnya